kaliji

Forum Replies Created

Viewing 5 posts - 1 through 5 (of 5 total)
  • Author
    Posts
  • in reply to: Comments from Blog Post “Sticky Finger’ Kali-Pi” #11793
    kaliji
    Participant

    Thank you very much for your attention and reactivity ,i really appreciate it.
    I followed the instruction same issue after reboot.
    Do you think it has to do with raspi-gpio , i was able to install the package but unable to run this command :sudo raspi-gpio get.
    I used this tuto :http://www.raspberrypi-spy.co.uk/2012/05/install-rpi-gpio-python-library/

    Config.txt:
    # Disable spi and i2c, we need these pins.
    dtparam=spi=off
    dtparam=i2c_arm=off

    # Set screen size and any overscan required
    overscan_left=0
    overscan_right=0
    overscan_top=0
    overscan_bottom=0
    framebuffer_width=800
    framebuffer_height=480

    # enable the DPI display
    enable_dpi_lcd=1
    display_default_lcd=1

    # set up the size to 800×480
    dpi_group=2
    dpi_mode=87

    # set up the hsync/vsync/clock polarity and format
    dpi_output_format=454661

    # set up the size to 800×480
    hdmi_timings=800 0 40 48 88 480 0 13 3 32 0 0 0 60 0 32000000 6

    *************************************************************************

    dmesg output :
    root@kali:~# dmesg
    [ 0.000000] Booting Linux on physical CPU 0x0
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 4.4.50-Re4son-v7+ (root@re4son-kali-pi) (gcc version 4.8.3 20140106 (prerelease) (crosstool-NG linaro-1.13.1-4.8-2014.01 – Linaro GCC 2013.11) ) #11 SMP Sun Jun 25 14:51:54 AEST 2017
    [ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
    [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
    [ 0.000000] Machine model: Raspberry Pi 3 Model B Rev 1.2
    [ 0.000000] cma: Reserved 8 MiB at 0x3a800000
    [ 0.000000] Memory policy: Data cache writealloc
    [ 0.000000] On node 0 totalpages: 241664
    [ 0.000000] free_area_init_node: node 0, pgdat 808c9900, node_mem_map b9fa6000
    [ 0.000000] Normal zone: 2124 pages used for memmap
    [ 0.000000] Normal zone: 0 pages reserved
    [ 0.000000] Normal zone: 241664 pages, LIFO batch:31
    [ 0.000000] [bcm2709_smp_init_cpus] enter (9520->f3003010)
    [ 0.000000] [bcm2709_smp_init_cpus] ncores=4
    [ 0.000000] PERCPU: Embedded 13 pages/cpu @b9f62000 s22592 r8192 d22464 u53248
    [ 0.000000] pcpu-alloc: s22592 r8192 d22464 u53248 alloc=13*4096
    [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 239540
    [ 0.000000] Kernel command line: 8250.nr_uarts=0 bcm2708_fb.fbwidth=800 bcm2708_fb.fbheight=480 bcm2708_fb.fbswap=1 dma.dmachans=0x7f35 bcm2709.boardrev=0xa22082 bcm2709.serial=0x689ee739 bcm2709.uart_clock=48000000 smsc95xx.macaddr=B8:27:EB:9E:E7:39 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000 dwc_otg.fiq_fix_enable=2 console=ttyS0,115200 kgdboc=ttyS0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait rootflags=noload net.ifnames=0
    [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [ 0.000000] Memory: 939044K/966656K available (6356K kernel code, 435K rwdata, 1728K rodata, 480K init, 771K bss, 19420K reserved, 8192K cma-reserved)
    [ 0.000000] Virtual kernel memory layout:
    vector : 0xffff0000 – 0xffff1000 ( 4 kB)
    fixmap : 0xffc00000 – 0xfff00000 (3072 kB)
    vmalloc : 0xbb800000 – 0xff800000 (1088 MB)
    lowmem : 0x80000000 – 0xbb000000 ( 944 MB)
    modules : 0x7f000000 – 0x80000000 ( 16 MB)
    .text : 0x80008000 – 0x807ed62c (8086 kB)
    .init : 0x807ee000 – 0x80866000 ( 480 kB)
    .data : 0x80866000 – 0x808d2c40 ( 436 kB)
    .bss : 0x808d5000 – 0x80995dec ( 772 kB)
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Hierarchical RCU implementation.
    [ 0.000000] Build-time adjustment of leaf fanout to 32.
    [ 0.000000] NR_IRQS:16 nr_irqs:16 16
    [ 0.000000] Architected cp15 timer(s) running at 19.20MHz (phys).
    [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
    [ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
    [ 0.000025] Switching to timer-based delay loop, resolution 52ns
    [ 0.000278] Console: colour dummy device 80×30
    [ 0.001355] console [tty1] enabled
    [ 0.001402] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
    [ 0.001471] pid_max: default: 32768 minimum: 301
    [ 0.001791] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [ 0.001835] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [ 0.002796] Disabling cpuset control group subsystem
    [ 0.002855] Initializing cgroup subsys io
    [ 0.002907] Initializing cgroup subsys memory
    [ 0.002971] Initializing cgroup subsys devices
    [ 0.003015] Initializing cgroup subsys freezer
    [ 0.003058] Initializing cgroup subsys net_cls
    [ 0.003127] CPU: Testing write buffer coherency: ok
    [ 0.003209] ftrace: allocating 21428 entries in 63 pages
    [ 0.053609] CPU0: update cpu_capacity 1024
    [ 0.053673] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
    [ 0.053706] [bcm2709_smp_prepare_cpus] enter
    [ 0.053848] Setting up static identity map for 0x8240 – 0x8274
    [ 0.055561] [bcm2709_boot_secondary] cpu:1 started (0) 17
    [ 0.055749] [bcm2709_secondary_init] enter cpu:1
    [ 0.055793] CPU1: update cpu_capacity 1024
    [ 0.055799] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
    [ 0.056194] [bcm2709_boot_secondary] cpu:2 started (0) 16
    [ 0.056358] [bcm2709_secondary_init] enter cpu:2
    [ 0.056381] CPU2: update cpu_capacity 1024
    [ 0.056387] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
    [ 0.056765] [bcm2709_boot_secondary] cpu:3 started (0) 17
    [ 0.056896] [bcm2709_secondary_init] enter cpu:3
    [ 0.056917] CPU3: update cpu_capacity 1024
    [ 0.056923] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
    [ 0.056985] Brought up 4 CPUs
    [ 0.057084] SMP: Total of 4 processors activated (153.60 BogoMIPS).
    [ 0.057113] CPU: All CPU(s) started in HYP mode.
    [ 0.057139] CPU: Virtualization extensions available.
    [ 0.057787] devtmpfs: initialized
    [ 0.068995] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
    [ 0.069373] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    [ 0.070113] pinctrl core: initialized pinctrl subsystem
    [ 0.070693] NET: Registered protocol family 16
    [ 0.075875] DMA: preallocated 4096 KiB pool for atomic coherent allocations
    [ 0.082746] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
    [ 0.082795] hw-breakpoint: maximum watchpoint size is 8 bytes.
    [ 0.082973] Serial: AMBA PL011 UART driver
    [ 0.083153] uart-pl011 3f201000.uart: could not find pctldev for node /soc/gpio@7e200000/uart0_pins, deferring probe
    [ 0.083359] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
    [ 0.155734] bcm2835-dma 3f007000.dma: DMA legacy API manager at f3007000, dmachans=0x1
    [ 0.156357] SCSI subsystem initialized
    [ 0.156558] usbcore: registered new interface driver usbfs
    [ 0.156669] usbcore: registered new interface driver hub
    [ 0.156788] usbcore: registered new device driver usb
    [ 0.163165] raspberrypi-firmware soc:firmware: Attached to firmware from 2017-04-05 11:49
    [ 0.190398] clocksource: Switched to clocksource arch_sys_counter
    [ 0.233602] FS-Cache: Loaded
    [ 0.233909] CacheFiles: Loaded
    [ 0.246382] NET: Registered protocol family 2
    [ 0.247291] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
    [ 0.247429] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
    [ 0.247640] TCP: Hash tables configured (established 8192 bind 8192)
    [ 0.247754] UDP hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.247823] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.248081] NET: Registered protocol family 1
    [ 0.248437] RPC: Registered named UNIX socket transport module.
    [ 0.248469] RPC: Registered udp transport module.
    [ 0.248497] RPC: Registered tcp transport module.
    [ 0.248524] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [ 0.249565] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
    [ 0.251041] futex hash table entries: 1024 (order: 4, 65536 bytes)
    [ 0.264525] VFS: Disk quotas dquot_6.6.0
    [ 0.264859] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [ 0.267174] FS-Cache: Netfs ‘nfs’ registered for caching
    [ 0.268104] NFS: Registering the id_resolver key type
    [ 0.268173] Key type id_resolver registered
    [ 0.268201] Key type id_legacy registered
    [ 0.273639] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.273814] io scheduler noop registered
    [ 0.273852] io scheduler deadline registered
    [ 0.273937] io scheduler cfq registered (default)
    [ 0.276577] BCM2708FB: allocated DMA memory fac10000
    [ 0.276625] BCM2708FB: allocated DMA channel 0 @ f3007000
    [ 0.288308] Console: switching to colour frame buffer device 100×30
    [ 0.298901] bcm2835-rng 3f104000.rng: hwrng registered
    [ 0.301785] vc-cma: Videocore CMA driver
    [ 0.304503] vc-cma: vc_cma_base = 0x00000000
    [ 0.307182] vc-cma: vc_cma_size = 0x00000000 (0 MiB)
    [ 0.309820] vc-cma: vc_cma_initial = 0x00000000 (0 MiB)
    [ 0.312625] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 mem_size:0x3f000000(1008 MiB)
    [ 0.330523] brd: module loaded
    [ 0.342010] loop: module loaded
    [ 0.345634] vchiq: vchiq_init_state: slot_zero = 0xbac80000, is_master = 0
    [ 0.349814] Loading iSCSI transport class v2.0-870.
    [ 0.353264] usbcore: registered new interface driver smsc95xx
    [ 0.356011] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
    [ 0.559013] Core Release: 2.80a
    [ 0.561646] Setting default values for core params
    [ 0.564306] Finished setting default values for core params
    [ 0.767343] Using Buffer DMA mode
    [ 0.770018] Periodic Transfer Interrupt Enhancement – disabled
    [ 0.772739] Multiprocessor Interrupt Enhancement – disabled
    [ 0.775395] OTG VER PARAM: 0, OTG VER FLAG: 0
    [ 0.778047] Dedicated Tx FIFOs mode
    [ 0.781040] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = 0xbac04000 dma = 0xfac04000 len=9024
    [ 0.786780] FIQ FSM acceleration enabled for :
    Non-periodic Split Transactions
    Periodic Split Transactions
    High-Speed Isochronous Endpoints
    Interrupt/Control Split Transaction hack enabled
    [ 0.801088] dwc_otg: Microframe scheduler enabled
    [ 0.801140] WARN::hcd_init_fiq:415: FIQ on core 1 at 0x8044a868
    [ 0.804110] WARN::hcd_init_fiq:416: FIQ ASM at 0x8044abc4 length 36
    [ 0.807125] WARN::hcd_init_fiq:441: MPHI regs_base at 0xbb87e000
    [ 0.810098] dwc_otg 3f980000.usb: DWC OTG Controller
    [ 0.812999] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
    [ 0.815974] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000
    [ 0.818886] Init: Port Power? op_state=1
    [ 0.821705] Init: Power Port (0)
    [ 0.824627] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
    [ 0.827479] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.830322] usb usb1: Product: DWC OTG Controller
    [ 0.833159] usb usb1: Manufacturer: Linux 4.4.50-Re4son-v7+ dwc_otg_hcd
    [ 0.836031] usb usb1: SerialNumber: 3f980000.usb
    [ 0.839656] hub 1-0:1.0: USB hub found
    [ 0.842478] hub 1-0:1.0: 1 port detected
    [ 0.845833] dwc_otg: FIQ enabled
    [ 0.845842] dwc_otg: NAK holdoff enabled
    [ 0.845850] dwc_otg: FIQ split-transaction FSM enabled
    [ 0.845881] Module dwc_common_port init
    [ 0.846132] usbcore: registered new interface driver usb-storage
    [ 0.849146] mousedev: PS/2 mouse device common for all mice
    [ 0.852668] bcm2835-cpufreq: min=600000 max=1200000
    [ 0.855654] sdhci: Secure Digital Host Controller Interface driver
    [ 0.858307] sdhci: Copyright(c) Pierre Ossman
    [ 0.861243] sdhost: log_buf @ bac07000 (fac07000)
    [ 0.920428] mmc0: sdhost-bcm2835 loaded – DMA enabled (>1)
    [ 0.925386] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
    [ 0.928140] mmc-bcm2835 3f300000.mmc: DMA channel allocated
    [ 0.980510] sdhci-pltfm: SDHCI platform and OF driver helper
    [ 0.983621] ledtrig-cpu: registered to indicate activity on CPUs
    [ 0.986482] hidraw: raw HID events driver (C) Jiri Kosina
    [ 0.989432] usbcore: registered new interface driver usbhid
    [ 0.992215] usbhid: USB HID core driver
    [ 0.995501] Initializing XFRM netlink socket
    [ 0.998242] NET: Registered protocol family 17
    [ 1.001086] Key type dns_resolver registered
    [ 1.004322] Registering SWP/SWPB emulation handler
    [ 1.007805] registered taskstats version 1
    [ 1.011861] Key type encrypted registered
    [ 1.014551] vc-sm: Videocore shared memory driver
    [ 1.017137] [vc_sm_connected_init]: start
    [ 1.018737] mmc0: host does not support reading read-only switch, assuming write-enable
    [ 1.021837] mmc0: new high speed SDHC card at address aaaa
    [ 1.022510] mmcblk0: mmc0:aaaa SS08G 7.40 GiB
    [ 1.026165] mmcblk0: p1 p2
    [ 1.032590] [vc_sm_connected_init]: end – returning 0
    [ 1.036568] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
    [ 1.039775] of_cfs_init
    [ 1.042630] of_cfs_init: OK
    [ 1.044161] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
    [ 1.045709] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
    [ 1.047253] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
    [ 1.050030] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
    [ 1.055946] Indeed it is in host mode hprt0 = 00021501
    [ 1.066242] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: noload
    [ 1.068900] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
    [ 1.074065] devtmpfs: mounted
    [ 1.077275] Freeing unused kernel memory: 480K (807ee000 – 80866000)
    [ 1.143762] mmc1: new high speed SDIO card at address 0001
    [ 1.230445] usb 1-1: new high-speed USB device number 2 using dwc_otg
    [ 1.233389] Indeed it is in host mode hprt0 = 00001101
    [ 1.382742] systemd[1]: System time before build time, advancing clock.
    [ 1.430712] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
    [ 1.433694] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
    [ 1.437440] hub 1-1:1.0: USB hub found
    [ 1.440500] hub 1-1:1.0: 5 ports detected
    [ 1.494555] NET: Registered protocol family 10
    [ 1.515360] random: systemd: uninitialized urandom read (16 bytes read, 52 bits of entropy available)
    [ 1.526383] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
    [ 1.536438] systemd[1]: Detected architecture arm.
    [ 1.559265] systemd[1]: Set hostname to <kali>.
    [ 1.632900] random: systemd: uninitialized urandom read (16 bytes read, 64 bits of entropy available)
    [ 1.647511] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 66 bits of entropy available)
    [ 1.655752] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 67 bits of entropy available)
    [ 1.668584] random: systemd-cryptse: uninitialized urandom read (16 bytes read, 68 bits of entropy available)
    [ 1.671943] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 68 bits of entropy available)
    [ 1.740467] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
    [ 1.838783] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
    [ 1.847755] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
    [ 1.852264] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
    [ 1.859628] smsc95xx v1.0.4
    [ 1.872294] random: systemd: uninitialized urandom read (16 bytes read, 71 bits of entropy available)
    [ 1.881280] random: systemd: uninitialized urandom read (16 bytes read, 71 bits of entropy available)
    [ 1.891071] random: systemd: uninitialized urandom read (16 bytes read, 71 bits of entropy available)
    [ 1.924264] smsc95xx 1-1.1:1.0 eth0: register ‘smsc95xx’ at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:9e:e7:39
    [ 2.067544] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
    [ 2.078105] systemd[1]: Listening on udev Kernel Socket.
    [ 2.087989] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
    [ 2.098241] systemd[1]: Created slice System Slice.
    [ 2.107536] systemd[1]: Reached target Encrypted Volumes.
    [ 2.116843] systemd[1]: Created slice User and Session Slice.
    [ 2.125740] systemd[1]: Listening on fsck to fsckd communication Socket.
    [ 2.134435] systemd[1]: Reached target Remote File Systems (Pre).
    [ 2.143170] systemd[1]: Reached target Swap.
    [ 2.151657] systemd[1]: Listening on Journal Socket (/dev/log).
    [ 2.159918] systemd[1]: Listening on Journal Socket.
    [ 2.190673] systemd[1]: Mounting POSIX Message Queue File System…
    [ 2.214835] systemd[1]: Starting Load Kernel Modules…
    [ 2.226603] systemd[1]: Mounting Debug File System…
    [ 2.238261] systemd[1]: Starting Create list of required static device nodes for the current kernel…
    [ 2.258947] systemd[1]: Listening on Syslog Socket.
    [ 2.269213] systemd[1]: Starting Journal Service…
    [ 2.280210] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
    [ 2.288257] systemd[1]: Reached target Paths.
    [ 2.296222] systemd[1]: Listening on udev Control Socket.
    [ 2.304118] systemd[1]: Reached target Slices.
    [ 2.312729] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
    [ 2.329401] systemd[1]: Reached target Remote File Systems.
    [ 2.340272] systemd[1]: Starting File System Check on Root Device…
    [ 2.349697] systemd[1]: Created slice system-getty.slice.
    [ 2.366004] systemd[1]: Mounted Debug File System.
    [ 2.374789] systemd[1]: Mounted POSIX Message Queue File System.
    [ 2.384662] systemd[1]: Started Load Kernel Modules.
    [ 2.398120] systemd[1]: Started Create list of required static device nodes for the current kernel.
    [ 2.410761] systemd[1]: Started Journal Service.
    [ 2.761907] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
    [ 3.259102] systemd-journald[139]: Received request to flush runtime journal from PID 1
    [ 3.583828] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
    [ 3.593947] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer
    [ 3.927813] usbcore: registered new interface driver brcmfmac
    [ 4.112219] brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Dec 15 2015 18:10:45 version 7.45.41.23 (r606571) FWID 01-cc4eda9c
    [ 4.142220] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code
    [ 4.155265] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code
    [ 4.158417] cfg80211: World regulatory domain updated:
    [ 4.161425] cfg80211: DFS Master region: unset
    [ 4.161563] cfg80211: (start_freq – end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
    [ 4.170176] cfg80211: (2402000 KHz – 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
    [ 4.173364] cfg80211: (2457000 KHz – 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
    [ 4.179579] cfg80211: (2474000 KHz – 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
    [ 4.182872] cfg80211: (5170000 KHz – 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
    [ 4.189109] cfg80211: (5250000 KHz – 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
    [ 4.195731] cfg80211: (5490000 KHz – 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
    [ 4.199324] cfg80211: (5735000 KHz – 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
    [ 4.202929] cfg80211: (57240000 KHz – 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
    [ 25.723801] random: nonblocking pool is initialized
    [ 26.241668] uart-pl011 3f201000.uart: no DMA platform data
    [ 27.342941] smsc95xx 1-1.1:1.0 eth0: hardware isn’t capable of remote wakeup
    [ 27.346358] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 28.040766] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 28.080721] brcmfmac: brcmf_add_if: ERROR: netdev:wlan0 already exists
    [ 28.080751] brcmfmac: brcmf_add_if: ignore IF event
    [ 28.086392] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 28.086443] brcmfmac: power management disabled
    [ 29.067327] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
    [ 29.078229] brcmfmac: brcmf_add_if: ERROR: netdev:wlan0 already exists
    [ 29.078250] brcmfmac: brcmf_add_if: ignore IF event
    [ 29.081604] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [ 29.132031] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 31.106085] Bluetooth: Core ver 2.21
    [ 31.106186] NET: Registered protocol family 31
    [ 31.106198] Bluetooth: HCI device and connection manager initialized
    [ 31.106222] Bluetooth: HCI socket layer initialized
    [ 31.106241] Bluetooth: L2CAP socket layer initialized
    [ 31.106277] Bluetooth: SCO socket layer initialized
    [ 31.120985] Bluetooth: HCI UART driver ver 2.3
    [ 31.121011] Bluetooth: HCI UART protocol H4 registered
    [ 31.121021] Bluetooth: HCI UART protocol Three-wire (H5) registered
    [ 31.121208] Bluetooth: HCI UART protocol BCM registered
    [ 31.293679] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    [ 31.293701] Bluetooth: BNEP filters: protocol multicast
    [ 31.293724] Bluetooth: BNEP socket layer initialized
    [ 31.436231] fuse init (API version 7.23)

    in reply to: Comments from Blog Post “Sticky Finger’ Kali-Pi” #11791
    kaliji
    Participant

    I just tried it now ,did mount /boot then followed the Install Device Tree Blob section ,rebooted and still the same .

    root@kali:~# sudo bash
    root@kali:~# mount /boot
    root@kali:~# cd ~
    root@kali:~# wget https://raw.githubusercontent.com/adafruit/Adafruit-DPI-Kippah/master/dt-blob.bin
    –2017-06-30 19:52:08– https://raw.githubusercontent.com/adafruit/Adafruit-DPI-Kippah/master/dt-blob.bin
    Resolving raw.githubusercontent.com (raw.githubusercontent.com)… 151.101.0.133, 151.101.64.133, 151.101.128.133, …
    Connecting to raw.githubusercontent.com (raw.githubusercontent.com)|151.101.0.133|:443… connected.
    HTTP request sent, awaiting response… 200 OK
    Length: 52314 (51K) [application/octet-stream]
    Saving to: ‘dt-blob.bin.4’

    dt-blob.bin.4 100%[===================>] 51.09K 307KB/s in 0.2s

    2017-06-30 19:52:08 (307 KB/s) – ‘dt-blob.bin.4’ saved [52314/52314]

    root@kali:~# sudo cp dt-blob.bin /boot/

    Then I copied the code to the config.txt file

    in reply to: Comments from Blog Post “Sticky Finger’ Kali-Pi” #11787
    kaliji
    Participant

    I did their instruction with Raspbian ,it works perfectly .But nothing with Kali.

    in reply to: Comments from Blog Post “Sticky Finger’ Kali-Pi” #11785
    kaliji
    Participant

    I just did it it’s still not working .

    in reply to: Comments from Blog Post “Sticky Finger’ Kali-Pi” #11781
    kaliji
    Participant

    I’m using this same configuration :
    https://learn.adafruit.com/adafruit-dpi-display-kippah-ttl-tft/installation
    I followed all the steps on your tutorial and tried all the different screen using the command :./re4son-pi-tft-setup -t ** -d /root ,none of them work.
    I’m struggling for days trying anything that I can found .
    Can you please provide me with any suggestions

Viewing 5 posts - 1 through 5 (of 5 total)